Full Site Search

Does the magnetizing machine trip the circuit breaker as soon as it starts up, or after a few cycles? Troubleshooting Causes of Circuit Breaker and Ground Fault Circuit Interrupter Trips—Jiuju Magnetizing Machine

End-to-End Solution for Magnetization Automation

Q1: Why does the circuit breaker trip as soon as I press the charging button on the magnetizing machine?

A: It’s most likely a problem with the capacitor’s insulation to ground. The magnetizing machine’s capacitor bank operates under high voltage for extended periods; if the insulating pads between the capacitor casings and the cabinet become damp or deteriorate, a short circuit to ground will occur as soon as the unit is energized, causing the circuit breaker to trip. Use a megohmmeter to measure the insulation resistance of the capacitor bank to ground; anything below 2 megohms is a failure. Last year, at a speaker factory in Dongguan, condensation had accumulated at the bottom of the cabinet, and the capacitor leads were submerged in water; as soon as charging began, the entire circuit tripped. After raising the capacitors and adding insulating pads, and installing moisture-proof heaters in the cabinet, there have been no further trips. Also, check whether the rectifier bridge has broken down; if a silicon stack breaks down, the AC current will short-circuit directly to ground, causing an instant trip.

Jiuju Complete Set of Magnetizers
Jiuju Complete Set of Magnetizers

Q2: It doesn't happen every time—why does it only happen once after seven or eight charges?

A: This type of intermittent tripping is the most frustrating; it’s usually caused by the contactor contacts becoming eroded, resulting in asynchronous engagement. If the three-phase contacts of the charging contactor are worn to different degrees, one phase will close before the others. This momentary current imbalance can trigger the circuit breaker’s instantaneous trip—the circuit breaker’s response time is only a few milliseconds, making it extremely sensitive. Remove the contactor and polish or replace the contacts; if the copper contacts have pits visible to the naked eye, they should be replaced. Another possibility is that the surge current during capacitor charging is too high, resulting in an improperly selected circuit breaker. For capacitive loads such as magnetizers, it is recommended to use a circuit breaker with a Type D trip curve, which operates only when the instantaneous trip current reaches 10 to 20 times the rated current, thereby minimizing false trips.

High-Precision Magnetizing Equipment
High-Precision Magnetizing Equipment

Q3: Why does the ground fault circuit interrupter keep tripping even though the insulation test with a megohmmeter shows it’s fine?

A: This is the most common false trip of a residual current device (RCD) caused by a magnetizing machine. An RCD detects leakage current to ground. When a magnetizing machine discharges, the pulse current contains a high-frequency component, and the parasitic capacitance between the capacitor and the machine housing generates high-frequency current to ground. Although this current does not pass through the human body, the RCD’s detection coil cannot distinguish this—it only detects the magnitude of the current. The solution is to run the magnetizer’s power supply circuit on a separate line that bypasses the workshop’s main RCD, or to replace it with an RCD that is insensitive to pulsed currents. However, please note that this does not mean you should remove the RCD; the magnetizer is high-voltage equipment, and safety measures must not be overlooked—a separate, appropriately rated RCD must be installed.

Magnetization of Magnetic Materials
3C Electronic Magnetization
Motor Rotor Magnetization
Car Speaker Magnetization
New Energy Vehicle Industry
Medical Equipment Industry
Other Industries
Jiuju Magnetization 100 Q&A: What Counts as a Defective Magnet

Jiuju Magnetization 100 Q&A: What Counts as a Defective Magnet

Nov 10, 2026

Defects in permanent magnets go beyond appearance: magn…

Magnetization 100 Q&A: Choosing the Magnet Operating Temperature

Magnetization 100 Q&A: Choosing the Magnet Operating Temperature

Nov 10, 2026

Operating temperature is the core constraint in magnet …

Precise Magnetization Control for AlNiCo Magnets: Case Video

Precise Magnetization Control for AlNiCo Magnets: Case Video

Oct 30, 2026

AlNiCo magnets keep stable flux thanks to a very low te…

How NdFeB Magnets Achieve Stable Magnetism: Case Video

How NdFeB Magnets Achieve Stable Magnetism: Case Video

Oct 9, 2026

Stable NdFeB performance requires the right grade, a co…

Magnetization 100 Q&A: Single-Pole vs Multi-Pole Magnetization

Magnetization 100 Q&A: Single-Pole vs Multi-Pole Magnetization

Nov 10, 2026

This video explains the difference between single-pole …

Video Demonstrating the Magnetization of Jiuju High-Frequency Drivers—Jiuju Magnetizer

Video Demonstrating the Magnetization of Jiuju High-Frequency Drivers—Jiuju Magnetizer

Sep 14, 2026

Case video: Video Demonstrating the Magnetization of Ji…

Unusual Noises and Power Loss in Motors? The Root Cause Is an Uneven Magnetic Field—Jiuju Magnetizing Machine
Quality Control for Mass-Produced Permanent Magnet Motors: Why Magnetic Field Measurement Is Essential—Jiuju...
How Critical Is Magnetization in Magnetic Switch Production?

How Critical Is Magnetization in Magnetic Switch Production?

Oct 29, 2026

In magnetic switches, magnetization controls holding fo…

Video Demonstrating Jiuju's Magnetization Process for Antique Speakers—Jiuju Magnetizer

Video Demonstrating Jiuju's Magnetization Process for Antique Speakers—Jiuju Magnetizer

Sep 13, 2026

Case video: Video Demonstrating Jiuju’s Magnetization P…

Video Demonstrating the Magnetization Process for Jiuju Speakers—Jiuju Magnetizer

Video Demonstrating the Magnetization Process for Jiuju Speakers—Jiuju Magnetizer

Sep 10, 2026

Case video: Video Demonstrating the Magnetization Proce…

Why Does the Tip “Stick” to the Screw? A Video Explanation of Magnetization—Jiuju Magnetizing Machine

Why Does the Tip “Stick” to the Screw? A Video Explanation of Magnetization—Jiuju Magnetizing Machine

Aug 2, 2026

Case video: Why Does the Tip “Stick” to the Screw? A Vi…

Video on Magnetizing Automotive Motor Rotors—Jiuju Magnetizing Machine

Video on Magnetizing Automotive Motor Rotors—Jiuju Magnetizing Machine

Jul 22, 2026

Case video: Video on Magnetizing Automotive Motor Rotor…

Video Case Study: Magnetizing Machine for Automotive Motor Rotors—Jiuju Magnetizing Machine

Video Case Study: Magnetizing Machine for Automotive Motor Rotors—Jiuju Magnetizing Machine

Jul 5, 2026

Case video: Video Case Study: Magnetizing Machine for A…

JiuJi four-station motor magnetizer: new energy automobile motor manufacturing efficien...
久巨充磁视频案例:医疗磁条充磁

久巨充磁视频案例:医疗磁条充磁

Jan 7, 2026

Case video: JiuJu Magnetic Stripe Magnetization Video C…

Video Guide on How to Select a Magnetizing Machine—Jiuju Magnetizing Machines

Video Guide on How to Select a Magnetizing Machine—Jiuju Magnetizing Machines

Aug 8, 2026

Case video: Video Guide on How to Select a Magnetizing …

A 20-Second Video Guide on How to Choose a Magnetizing Machine—Jiuju Magnetizing Machine

A 20-Second Video Guide on How to Choose a Magnetizing Machine—Jiuju Magnetizing Machine

Jul 21, 2026

Case video: A 20-Second Video Guide on How to Choose a …

3000V Magnetizing Machine and Chiller Operation Demonstration Video—Jiuju Magnetizing Machine

3000V Magnetizing Machine and Chiller Operation Demonstration Video—Jiuju Magnetizing Machine

Jul 3, 2026

Case video: 3000V Magnetizing Machine and Chiller Opera…

Video on the Wiring Procedure for a 3000V General-Purpose Industrial Magnetizer—Jiuju Magnetizer

Video on the Wiring Procedure for a 3000V General-Purpose Industrial Magnetizer—Jiuju Magnetizer

Jul 2, 2026

Case video: Video on the Wiring Procedure for a 3000V G…

Previous. NEXT STORY.

en_USEnglish