Full Site Search

JIUJU Speaker Magnetization Practical Guide: Principles and Hands-On Procedures

End-to-End Solution for Magnetization Automation

The core of the horn's ability to produce sound is the interaction between the magnetic field and the electric current. When the current flows through the voice coil of the horn, it will be subjected to forces in the magnetic field, which will drive the diaphragm to vibrate and eventually form sound. The strength of the magnetic field provided by the magnet will directly affect the performance of the speaker.

The core purpose of magnetization is to make horn magnets have stable and appropriate magnetic properties. It is based on the principle of electromagnetic induction, through the external input of pulse current to generate instantaneous strong magnetic field, prompting the magnetic domains inside the magnet tends to regularize the arrangement, so as to achieve the enhancement of the magnetic properties.

undefined

II. Pre-magnetization preparations

Before magnetizing, you need to make sure that the magnetizing equipment is in good condition and the parameters are set to meet the requirements. JiuJu speakers have their own specifications for magnetization, so you should refer to the product manual and carefully adjust the key parameters such as magnetizing voltage, current and pulse width.

At the same time, prepare the horn unit to be magnetized, check the appearance of the speakers one by one whether there is any damage, and confirm that the voice coil is in normal working condition, so as to avoid affecting the magnetization effect due to the hidden danger in the early stage.

undefined

1. Place the JUJI horn on the magnetizing fixture to ensure accurate positioning and secure fixing of the horn and to reduce the effect of displacement on the magnetizing effect during the magnetizing process.

2. After completing the line connection between the magnetizing equipment and the horn, check the connection status again to see if it is reliable, so as to avoid abnormal magnetization or damage to the equipment caused by poor contact.

3. Start the magnetizing device and it will release the pulse current according to the preset parameters to complete the magnetizing operation. A slight "pop" sound may be heard during the process, which is a normal reaction to the instantaneous establishment of a magnetic field.

4. After the magnetization is finished, do not remove the horn immediately, need to stay for a short time to let the magnet internal magnetic domain fully stabilized. After that, carefully remove the horn, and then carry out subsequent performance testing.

undefined

After the magnetization is completed, the magnetic field strength of the speaker magnet can be tested with the help of a professional Gaussmeter to see if it meets the preset standards.

At the same time, the magnetized speaker is connected to a simple audio test circuit to play audio signals of different frequencies. Through the sense of hearing the initial judgment of whether the sound quality is clear and full, to observe whether there are abnormal noises or distortion, so as to assess the performance of the use of the magnetized.

Magnetization of Magnetic Materials
3C Electronic Magnetization
Motor Rotor Magnetization
Car Speaker Magnetization
New Energy Vehicle Industry
Medical Equipment Industry
Jiuju Magnetization 100 Q&A: What Counts as a Defective Magnet

Jiuju Magnetization 100 Q&A: What Counts as a Defective Magnet

Nov 10, 2026

Defects in permanent magnets go beyond appearance: magn…

Magnetization 100 Q&A: Choosing the Magnet Operating Temperature

Magnetization 100 Q&A: Choosing the Magnet Operating Temperature

Nov 10, 2026

Operating temperature is the core constraint in magnet …

Precise Magnetization Control for AlNiCo Magnets: Case Video

Precise Magnetization Control for AlNiCo Magnets: Case Video

Oct 30, 2026

AlNiCo magnets keep stable flux thanks to a very low te…

How NdFeB Magnets Achieve Stable Magnetism: Case Video

How NdFeB Magnets Achieve Stable Magnetism: Case Video

Oct 9, 2026

Stable NdFeB performance requires the right grade, a co…

轴向磁通电机多极充磁难点在哪?久巨工艺解答

轴向磁通电机多极充磁难点在哪?久巨工艺解答

Nov 19, 2026

轴向磁通电机磁钢铺在盘面、磁场垂直盘面、极数又多,难点集中在磁路方向、极间对位与热变形。说明专用轴向极头、角度定位销与多点扫描验收的做法。

电机充磁后转矩脉动大如何解决?久巨工艺解析

电机充磁后转矩脉动大如何解决?久巨工艺解析

Nov 19, 2026

转矩脉动大要先分清是电磁设计的齿槽转矩还是制造一致性的极间不均。用反电动势与逐极表磁定位,再从极头对位、能量闭环、磁通分组与斜极设计协同改善。

久巨人形机器人关节磁钢怎么保证充磁一致性?

久巨人形机器人关节磁钢怎么保证充磁一致性?

Nov 19, 2026

关节磁钢小、薄、极数多,难点不在能不能充上,而在每一件每一极都一样。分三层管控一致性,用仿形胎具解决薄壁定位,能量闭环全检后按磁通分组配对。

扬声器喇叭充磁后音质差异大怎么办?久巨电声行业答疑

扬声器喇叭充磁后音质差异大怎么办?久巨电声行业答疑

Nov 19, 2026

同一批喇叭充完磁听感不一致,问题常在磁隙磁通而非装配。说明磁通偏低与不均如何影响灵敏度、失真与谐波,以及充磁端四个来源、稳定化处理与分档配对。

轴向磁通电机多极充磁难点在哪?久巨工艺解答

轴向磁通电机多极充磁难点在哪?久巨工艺解答

Nov 19, 2026

轴向磁通电机磁钢铺在盘面、磁场垂直盘面、极数又多,难点集中在磁路方向、极间对位与热变形。说明专用轴向极头、角度定位销与多点扫描验收的做法。

电机充磁后转矩脉动大如何解决?久巨工艺解析

电机充磁后转矩脉动大如何解决?久巨工艺解析

Nov 19, 2026

转矩脉动大要先分清是电磁设计的齿槽转矩还是制造一致性的极间不均。用反电动势与逐极表磁定位,再从极头对位、能量闭环、磁通分组与斜极设计协同改善。

久巨人形机器人关节磁钢怎么保证充磁一致性?

久巨人形机器人关节磁钢怎么保证充磁一致性?

Nov 19, 2026

关节磁钢小、薄、极数多,难点不在能不能充上,而在每一件每一极都一样。分三层管控一致性,用仿形胎具解决薄壁定位,能量闭环全检后按磁通分组配对。

扬声器喇叭充磁后音质差异大怎么办?久巨电声行业答疑

扬声器喇叭充磁后音质差异大怎么办?久巨电声行业答疑

Nov 19, 2026

同一批喇叭充完磁听感不一致,问题常在磁隙磁通而非装配。说明磁通偏低与不均如何影响灵敏度、失真与谐波,以及充磁端四个来源、稳定化处理与分档配对。

轴向磁通电机多极充磁难点在哪?久巨工艺解答

轴向磁通电机多极充磁难点在哪?久巨工艺解答

Nov 19, 2026

轴向磁通电机磁钢铺在盘面、磁场垂直盘面、极数又多,难点集中在磁路方向、极间对位与热变形。说明专用轴向极头、角度定位销与多点扫描验收的做法。

电机充磁后转矩脉动大如何解决?久巨工艺解析

电机充磁后转矩脉动大如何解决?久巨工艺解析

Nov 19, 2026

转矩脉动大要先分清是电磁设计的齿槽转矩还是制造一致性的极间不均。用反电动势与逐极表磁定位,再从极头对位、能量闭环、磁通分组与斜极设计协同改善。

久巨人形机器人关节磁钢怎么保证充磁一致性?

久巨人形机器人关节磁钢怎么保证充磁一致性?

Nov 19, 2026

关节磁钢小、薄、极数多,难点不在能不能充上,而在每一件每一极都一样。分三层管控一致性,用仿形胎具解决薄壁定位,能量闭环全检后按磁通分组配对。

扬声器喇叭充磁后音质差异大怎么办?久巨电声行业答疑

扬声器喇叭充磁后音质差异大怎么办?久巨电声行业答疑

Nov 19, 2026

同一批喇叭充完磁听感不一致,问题常在磁隙磁通而非装配。说明磁通偏低与不均如何影响灵敏度、失真与谐波,以及充磁端四个来源、稳定化处理与分档配对。

轴向磁通电机多极充磁难点在哪?久巨工艺解答

轴向磁通电机多极充磁难点在哪?久巨工艺解答

Nov 19, 2026

轴向磁通电机磁钢铺在盘面、磁场垂直盘面、极数又多,难点集中在磁路方向、极间对位与热变形。说明专用轴向极头、角度定位销与多点扫描验收的做法。

电机充磁后转矩脉动大如何解决?久巨工艺解析

电机充磁后转矩脉动大如何解决?久巨工艺解析

Nov 19, 2026

转矩脉动大要先分清是电磁设计的齿槽转矩还是制造一致性的极间不均。用反电动势与逐极表磁定位,再从极头对位、能量闭环、磁通分组与斜极设计协同改善。

久巨人形机器人关节磁钢怎么保证充磁一致性?

久巨人形机器人关节磁钢怎么保证充磁一致性?

Nov 19, 2026

关节磁钢小、薄、极数多,难点不在能不能充上,而在每一件每一极都一样。分三层管控一致性,用仿形胎具解决薄壁定位,能量闭环全检后按磁通分组配对。

扬声器喇叭充磁后音质差异大怎么办?久巨电声行业答疑

扬声器喇叭充磁后音质差异大怎么办?久巨电声行业答疑

Nov 19, 2026

同一批喇叭充完磁听感不一致,问题常在磁隙磁通而非装配。说明磁通偏低与不均如何影响灵敏度、失真与谐波,以及充磁端四个来源、稳定化处理与分档配对。

轴向磁通电机多极充磁难点在哪?久巨工艺解答

轴向磁通电机多极充磁难点在哪?久巨工艺解答

Nov 19, 2026

轴向磁通电机磁钢铺在盘面、磁场垂直盘面、极数又多,难点集中在磁路方向、极间对位与热变形。说明专用轴向极头、角度定位销与多点扫描验收的做法。

电机充磁后转矩脉动大如何解决?久巨工艺解析

电机充磁后转矩脉动大如何解决?久巨工艺解析

Nov 19, 2026

转矩脉动大要先分清是电磁设计的齿槽转矩还是制造一致性的极间不均。用反电动势与逐极表磁定位,再从极头对位、能量闭环、磁通分组与斜极设计协同改善。

久巨人形机器人关节磁钢怎么保证充磁一致性?

久巨人形机器人关节磁钢怎么保证充磁一致性?

Nov 19, 2026

关节磁钢小、薄、极数多,难点不在能不能充上,而在每一件每一极都一样。分三层管控一致性,用仿形胎具解决薄壁定位,能量闭环全检后按磁通分组配对。

扬声器喇叭充磁后音质差异大怎么办?久巨电声行业答疑

扬声器喇叭充磁后音质差异大怎么办?久巨电声行业答疑

Nov 19, 2026

同一批喇叭充完磁听感不一致,问题常在磁隙磁通而非装配。说明磁通偏低与不均如何影响灵敏度、失真与谐波,以及充磁端四个来源、稳定化处理与分档配对。

NEXT STORY.

en_USEnglish