Axial Flux Motors: How to Design and Select a Dedicated Magnetizing Coil
轴向磁通的磁钢铺在大直径盘面上,磁场沿轴向穿过气隙,这决定了线圈不能照搬径向那套。选型要回答三个问题:覆盖多大面积、怎么补气隙、连续生产时热漂移怎么控。
久巨扇形分区线圈与磁钢覆盖原理图JIUJU Sector Zoned Coil and Magnet Coverage Principle覆盖面积决定能量效率
久巨轴向充磁气隙与连续生产热漂移图JIUJU Axial Magnetization Air Gap and Continuous Production Thermal Drift盘式磁钢是扇形分块排布的,线圈如果只对着中心区域,边缘那几块就充不足。合理的做法是按磁钢的投影形状做扇形或环形分区,让每一块都在有效场强范围内,而不是靠加大总能量去照顾远处。
分区之后还要解决同步。多组线圈同时放电,回路阻抗不一致就会出现先后和强弱差,磁钢之间的磁通就散了。
气隙大,能量需求就不线性
轴向结构的气隙通常比径向大,场强随距离衰减很快。为了在磁钢表面达到饱和场,线圈要么贴近,要么提高电流密度,两条路都要付出代价:贴近会干涉装配,提高电流密度会加剧发热。
实际项目里通常是在工装允许的最近距离上定线圈,再用脉宽和电流波形去补剩下的差额。
连续生产的热漂移是隐形误差
久巨轴向磁通电机盘式磁钢充磁结构图JIUJU Axial Flux Motor Disc Magnet Magnetization Structure线圈温度上去,电阻变大,同样设定下峰值电流就下来了。前几十件正常,后面慢慢偏低,这种漂移最难发现。按久巨的经验,多盘连续充磁必须把线圈温度和放电间隔纳入工艺窗口,必要时用温度补偿修正能量设定。
关键要点
● 线圈按磁钢投影形状分区,避免靠加大总能量照顾边缘
● 多组线圈同步放电,回路阻抗要配平
● 轴向气隙大,先在工装允许的最近距离定线圈,再用波形补差额
● 把线圈温度与放电间隔写进工艺窗口,防止连续生产漂移
常见问答
Q:径向자화 코일能直接改成轴向用吗?
A:通常不行。磁场方向与覆盖面积都不同,改绕只能应急,效率和均匀性都会打折。
Q:双边定子的结构要两次充磁吗?
A:多数设计是一次完成,两侧线圈同步放电。分开充容易在中间磁路上产生抵消。
Q:盘式磁钢分块多,怎么保证极性不错?
A:靠工装定位加分区极性检测。块数越多,机械防错越必要。
자성 물질의 자화
3C 전자 자화
전기 모터용 로터 자화
혼 스피커 자화
신에너지 자동차 산업
의료 기계 산업
기타 산업

11월 10, 2026
Defects in permanent magnets go beyond appearance: magn…

11월 10, 2026
Operating temperature is the core constraint in magnet …

10월 30, 2026
AlNiCo magnets keep stable flux thanks to a very low te…

10월 9, 2026
Stable NdFeB performance requires the right grade, a co…

11월 13, 2025
Magnetizing magnetic charging heads for phones: matchin…

11월 11, 2025
The Jiuju electronic magnetizer balances performance an…

11월 10, 2026
This video explains the difference between single-pole …

9월 14, 2026
Case video: Video Demonstrating the Magnetization of Ji…

9월 6, 2026
Motor noise and torque loss often trace back to uneven …

9월 5, 2026
Why surface flux inspection is indispensable for volume…

10월 29, 2026
In magnetic switches, magnetization controls holding fo…

9월 13, 2026
Case video: Video Demonstrating Jiuju’s Magnetization P…

9월 10, 2026
Case video: Video Demonstrating the Magnetization Proce…

8월 2, 2026
Case video: Why Does the Tip “Stick” to the Screw? A Vi…

7월 22, 2026
Case video: Video on Magnetizing Automotive Motor Rotor…

7월 5, 2026
Case video: Video Case Study: Magnetizing Machine for A…

11월 10, 2025
The Jiuju four-station motor magnetizer improves effici…

1월 7, 2026
Case video: JiuJu Magnetic Stripe Magnetization Video C…

8월 8, 2026
Case video: Video Guide on How to Select a Magnetizing …

7월 21, 2026
Case video: A 20-Second Video Guide on How to Choose a …

7월 3, 2026
Case video: 3000V Magnetizing Machine and Chiller Opera…

7월 2, 2026
Case video: Video on the Wiring Procedure for a 3000V G…