Why NdFeB Magnets Crack with a Bang During Magnetization: Prevention
Why NdFeB Magnets Crack with a Bang During Magnetization: Prevention
Magnetizing Process Popular-Science Series · JUJU Automation
充磁瞬间听到清脆的“啪”声,随后发现磁体裂开或崩角,是钕铁硼充磁中最典型的失效形式。这类问题多与材料脆性和充磁过程的力学载荷有关,而不是单纯的“磁太强”。
(一)电磁力是主因
久巨为什么钕铁硼充磁时会突然开裂
WhyMagnetCracksSuddenlyDuringMagnetization脉冲强磁场在磁体与导电镀层中产生涡流,涡流与磁场相互作用形成瞬时电磁力;多极充磁时,相邻磁极之间本身存在较强排斥力,能量越高、极距越窄,内应力越集中。钕铁硼抗拉强度低、脆性大,一旦局部应力超过材料强度,就会沿晶界开裂。
(二)来料与工装的叠加影响
久巨钕铁硼充磁开裂还要排查哪些因素
FactorsToCheckWhenMagnetsCrack来料本身已存在微裂纹、崩边、镀层起泡,或倒角与尺寸公差不足,都会成为应力集中点,薄壁、细长、异形磁体尤其敏感。夹具夹持过紧、定位面不平、夹爪为硬性点接触,则会把放电瞬间的机械冲击直接传到磁体上;线圈与工件间隙过小、放电时工件跳动,同样会诱发碎裂。实际排查时,可先看碎裂位置是否集中在磁极交界处或夹持接触点,据此判断是磁路应力还是装夹应力所致。
(三)预防措施
久巨如何降低钕铁硼充磁过程中的开裂风险
HowToReduceMagnetizationCrackingRisk优化磁体结构,增加倒角与圆角,避免尖角与薄壁突变;加强来料检验,筛除裂纹、崩角与镀层不良件;改进工装,采用面接触与柔性夹持,保证工件放电时稳定不跳动;工艺上采取分级充磁,先用较低能量预充磁,再补足到饱和,减小单次冲击。同时对易裂规格建立首件试充磁流程,确认参数无误后再批量投产。
久巨自动化在充磁工装与电源参数上做配套调试,针对易裂规格设定能量梯度与夹持方式,在保证饱和的前提下降低碎裂风险,减少磁体报废与产线停机。
자성 물질의 자화
3C 전자 자화
전기 모터용 로터 자화
혼 스피커 자화
신에너지 자동차 산업
의료 기계 산업
기타 산업

11월 10, 2026
Defects in permanent magnets go beyond appearance: magn…

11월 10, 2026
Operating temperature is the core constraint in magnet …

10월 30, 2026
AlNiCo magnets keep stable flux thanks to a very low te…

10월 9, 2026
Stable NdFeB performance requires the right grade, a co…

11월 13, 2025
Magnetizing magnetic charging heads for phones: matchin…

11월 11, 2025
The Jiuju electronic magnetizer balances performance an…

11월 10, 2026
This video explains the difference between single-pole …

9월 14, 2026
Case video: Video Demonstrating the Magnetization of Ji…

9월 6, 2026
Motor noise and torque loss often trace back to uneven …

9월 5, 2026
Why surface flux inspection is indispensable for volume…

10월 29, 2026
In magnetic switches, magnetization controls holding fo…

9월 13, 2026
Case video: Video Demonstrating Jiuju’s Magnetization P…

9월 10, 2026
Case video: Video Demonstrating the Magnetization Proce…

8월 2, 2026
Case video: Why Does the Tip “Stick” to the Screw? A Vi…

7월 22, 2026
Case video: Video on Magnetizing Automotive Motor Rotor…

7월 5, 2026
Case video: Video Case Study: Magnetizing Machine for A…

11월 10, 2025
The Jiuju four-station motor magnetizer improves effici…

1월 7, 2026
Case video: JiuJu Magnetic Stripe Magnetization Video C…

8월 8, 2026
Case video: Video Guide on How to Select a Magnetizing …

7월 21, 2026
Case video: A 20-Second Video Guide on How to Choose a …

7월 3, 2026
Case video: 3000V Magnetizing Machine and Chiller Opera…

7월 2, 2026
Case video: Video on the Wiring Procedure for a 3000V G…